张孜昭,许晓嫦,夏卿坤

• 1:中南大学材料科学与工程学院
• 2:中南大学有色金属材料科学与工程教育部重点实验室
• 3:长沙大学机电工程学院

摘要(Abstract)：

采用硬度检测、透射电镜观察、选区电子衍射等方法,研究了Al-Cu合金固溶态、含θ′相和含θ相的试样在强变形诱导析出相低温回溶后的加热退火过程中晶粒尺寸、高角晶界百分比及组织结构和硬度的变化。试验结果显示:当退火温度低于150℃时,Al-Cu合金三种状态的试样其晶粒尺寸与高角晶界的百分数基本上没有变化;加热温度至200℃以上后,晶粒尺寸、高角晶界百分比开始增加;加热至250℃时,固溶态试样的晶粒尺寸长大至100μm左右,含析出相的试样晶粒尺寸保持在10.0～15.0μm。在250℃退火50min后,固溶态试样的硬度值一直低于含θ′、θ析出相试样的硬度值。

关键词(KeyWords)： Al-Cu合金;强塑性变形;析出相回溶;热稳定性

Abstract:

Keywords:

基金项目(Foundation): 湖南省自然科学基金资助项目(05JJ40005);; 湖南省科技攻关项目(2007FJ3085)

作者(Author): 张孜昭,许晓嫦,夏卿坤

DOI: 10.13289/j.issn.1009-6264.2010.08.017

参考文献(References)：

• [1]Gao N,Starink M J,Furukawa M,et al.Evolution of microstructure and precipitation in heat-treatable aluminium alloys during ECA pressing and subsequent heat treatment[J].Materials Science Forum,2006,503-504:275-280.
• [2]Valiev R Z,Langdon T G.Principles of equal-channel angular pressing as a processing tool for grain refinement[J].Progress in Materials Science,2006,51:881-981.
• [3]Xu C,Furukawa M,Horita Z,et al.Influence of ECAP on precipitate distributions in a spray-cast aluminum alloy[J].Acta Materialia,2005,53:749-758.
• [4]Cizek J,Prochazka I,Smola B,etal.Microstructure and thermal stability of ultra fine grained Mg-based alloys prepared by high-pressure torsion[J].Materials Science and Engineering A,2007,462:121-126.
• [5]Zhilyaev A P,Langdon T G.Using high-pressure torsion for metal processing:fundamentals and applications[J].Progress in Materials Science,2008,53:893-979.
• [6]Kwan C,Wang Z R,Kang S B.Mechanical behavior and microstructural evolution upon annealing of the accumulative roll-bonding(ARB)processed Al alloy1100[J].Materials Science and Engineering A,2008,480:148-159.
• [7]Min B K,Kim H W,Kang S B.Effect of Al3Sc precipitate on the microstructural evolution during accumulative roll bonding in Al-0.2wt%Sc alloy[J].Journal of Materials Processing Technology.2005,162-163:355-361.
• [8]Cherukuri B,Nedkova T S,Srinivasan R.A comparison of the properties of SPD-processed AA-6061by equal-channel angular pressing multi-axial compressions/forgings and accumulative roll bonding[J].Materials Science and Engineering A,2005,410-411:394-397.
• [9]Cherukuri B,Srinivasan R.Properties of AA6061processed by multi-axial compressions/forging(MAC/F)[J].Materials and Manufacturing Processes,2006,21(5):519-525.
• [10]党朋,许晓嫦,刘志义,等.铝合金等径角挤压和多向压缩变形中析出相的回溶研究[J].材料热处理学报,2007,28(5):82-85.DANG Peng,XU Xiao-chang,LIU Zhi-yi,et al.Investigation on dissolution of precipitates in Al alloy deformed by equal-channel angular pressing and multi-axial compression[J].Transactions of Materials and Heat Treatment,2007,28(5):82-85.
• [11]Murayama M,Horita Z,Hono K.Microstructure of two-phase Al-1.7at%Cu Alloy deformed by equal-channel angular pressing[J].Acta Materialia,2001,49(1):21-29.
• [12]Kang S B,Lim C Y,Kim H W,et al.Microstructure evolution and hardening behavior of2024aluminum alloy processed by severe plastic deformation[J].Materials Science Forum,2002,396-402(2):1163-1168.
• [13]XU Xiao-chang,LIU Zhi-yi,LI Yun-tao,et al.Evolution of precipitates of Al-Cu alloy during equal-channel angular pressing at room temperature[J].Transactions of Nonferrous Metals Society of China,2008,18(5):1047-1052.
• [14]郑子樵.材料科学基础[M].长沙:中南大学出版社,2005:403-406.
• [15]Furukawa M,Horita Z,Zhilyaev A P,et al.Developing ultrafine-grained microstructures through the use of severe plastical deformation[J].Mater Science Forum,2003,42(6):2631-2636.
• [16]Heason C P,Prangnell P B.Grain refinement and texture evolution during the deformation of Al to ultra-high Strains by accumulative roll bonding(ARB)[J].Materials Science Forum,2002,396-402(1):429-434.
• [17]Prangnell P H,Bowen J R,Apps P J.Ultra-fine grain structure in aluminum alloys by severe deformation processing[J].Material Science and Engineering A,2004,375-377:178-185.
• [18]Dobatkin S V.On the increase of thermal stability of ultrafine grained material obtained by severe plastic deformation[J].Material Science Forum,2003,426-432:2699-2704.
• [19]Lee S,Utsunomiya A,Akamatsu H,et al.Influence of scandium and zirconium on grain stability and superplastic ductilities in ultrafine-grained Al-Mg alloys[J].Acta Materialia,2002,50(3):553-564.
• [20]XU C,Furukawa M,Horita Z,et al.Using ECAP to achieve grain refinement,precipitate fragmentation and high strain rate superplasticity in a spray-cast aluminum alloy[J].Acta Materialia,2003,51(20):6139-6149.
• [21]Mao J,Kang S B,Park J O.Grain refinement,thermal stability and tensile properties of2024aluminum alloy after equal-channel angular pressing[J].Journal of Materials Processing Technology,2005,159(3):314-320.
• [22]Langdon T G.The principles of grain refinement in equal-channel angular pressing[J].Mater Sci Eng A,2007,462(1-2):3-11.
• [23]Komura S,Furukawa M,Horita Z.Optimizing the procedure of equal-channel angular pressing for maximum superplasticity[J].Materials Science and Engineering A,2001,297(1-2):111-118.
• [24]CHANG Si-yong,Lee J G,Park K T,et al.Microstructures and mechanical of equal channel angular pressed5083Al alloy[J].Materials Transactions,2001,42(6):1074-1080.
• [25]WANG Jing-tao,Horita Z,Furukawa M,et al.An investigation of ductility and microstructural evolution in an Al-3%Mg alloy with submicron grain size[J].Journal of Materials Research,1993,8(11):2810-2818.
• [26]Wang Z C,Prangnell P B.Microstructure refinement and mechanical properties of severely deformed Al-Mg-Li alloy[J].Materials Science and Engineering A,2002,328(1-2):87-97.

文章评论(Comment)：