柳培,王爱琴,郝世明,谢敬佩

• 1:河南科技大学材料科学与工程学院
• 2:河南科技大学有色金属共性技术河南省协同创新中心
• 3:河南科技大学物理工程学院

摘要(Abstract)：

采用真空热压烧结工艺在580℃下制备了35%(体积分数)SiCp/2024铝基复合材料,利用扫描电镜(SEM)、透射电镜(TEM)、能谱(EDS)、高分辨透射电镜(HRTEM)对复合材料热处理过程中微观组织进行了表征,研究了热压烧结后复合材料的析出相的微观结构以及析出相在热处理过程的演变规律。结果表明,热压烧结后复合材料中存在许多粗大析出相颗粒,包括Al4Cu9,Al2Cu,Al18Mg3Mn2,Al5Cu6Mg2和Al7Cu2Fe。随着固溶温度的提高,粗大析出相颗粒逐渐回溶到Al基体中,当固溶温度达到510℃时,粗大析出相颗粒几乎全部回溶到基体中,但还存在少量的难溶相。复合材料经510℃固溶2 h+190℃时效9 h后,除了少量的难溶相,许多圆盘状纳米析出相Al2Cu和棒针状纳米析出相Al2Cu Mg弥散分布于基体中且与基体的界面为错配度较小的半共格界面,圆盘状纳米析出相的直径为50~200 nm,棒针状纳米析出相长度为100~150 nm。

关键词(KeyWords)： SiCp/Al基复合材料;粉末冶金;热处理;微观组织

Abstract:

Keywords:

基金项目(Foundation): 国家自然科学基金(51371077)

作者(Author): 柳培,王爱琴,郝世明,谢敬佩

DOI: 10.13289/j.issn.1009-6264.2015.03.002

参考文献(References)：

• [1]Wang Z,Song M,Sun C,et al.Effect of particle size and distribution on the mechanical properties of Si C reinforced Al-Cu alloy composites[J].Materials Science and Engineer A,2011,528(3):1131-1137.
• [2]Sharifi E M,Karimzadeh F,Enayati M H.Fabrication and evaluation of mechanical and tribological properties of boron carbide reinforced aluminum matrix nanocomposites[J].Materials and Design,2011,32(6):3263-3271.
• [3]Bathula S,Anandani R C,Dhar A,et al.Microstructural features and mechanical properties of Al 5083/Si Cp metal matrix nanocomposites produced by high energy ball milling and spark plasma sintering[J].Materials Science and Engineer A,2012,545:97-102.
• [4]Hafizpour H R,Simchi A,Parvizi S.Analysis of the compaction behavior of Al-Si C nanocomposites using linear and non-linear compaction equations[J].Advanced Powder Technology,2010,21(3):273-278.
• [5]Bekheet N E,Gadelrab R M,Salah M F,et al.The effects of aging on the hardness and fatigue behavior of 2024 Al alloy/Si C composites[J].Materials and Design,2002,23(2):153-159.
• [6]Durbadal M,Srinath V.Effect of heat treatment on microstructure and interface of Si C particle reinforced 2124 Al matrix composite[J].Materials Characterization,2013,85:73-81.
• [7]Pal S,Mitra R,Bhanuprasad V V.Aging behaviour of Al-Cu-Mg alloy-Si C composites[J].Materials Science and Engineer A,2008,480(1/2):496-505.
• [8]Appendino P,Badini C,Marino F,et al.6061 aluminum alloy-Si C particulate composite:a comparison between aging behavior in T4 and T6 treatment[J].Materials Science and Engineer A,1991,135:275-279.
• [9]Cheng S,Zhao Y H,Zhu Y T,et al.Optimizing the strength and ductility of fine structured 2024 Al alloy by nano-precipitation[J].Acta Materialia2007,55(17):5822-5832.
• [10]Mousavi Abarghouie S M R,Seyed Reihani S M.Aging behavior of a 2024 Al alloy-Si Cp composite[J].Materials and Design,2010,31(5):2368-2374.
• [11]Nie C Z,Gu J J,Liu J L,et al.Investigation on microstructures and interface character of B4C particles reinforced 2024Al matrix composites fabricated by mechanical alloying[J].Journal of Alloys and Compounds,2008,454(1/2):118-122.
• [12]Jin P,Xiao B L,Wang Q Z,et al.Effect of solution temperature on aging behavior and properties of Si Cp/Al-Cu-Mg composites[J].Materials Science and Engineer A,2011,528(3):1504-1511.
• [13]李培跃,熊柏青,张永安,等.2D70耐热铝合金显微组织均匀化热处理[J].中国有色金属学报,2010,20(11):2101-2105.LI Pei-yue,XIONG Bai-qing,ZHANG Yong-an,et al.Homogenization treatment and microstructure of semicontinous casting ingot of 2D70 heatresistance aluminum alloy[J].The Chinese Journal of Nonferrous Metals,2010,20(11):2101-2105.
• [14]熊创贤,邓运来,万里,等.7050铝合金板在固溶过程中微结构与织构的演变[J].中国有色金属学报,2010,20(3):427-434.XIONG Chuang-xian,DENG Yun-lai,WAN Li,et al.Evolutions of microstructures and textures of 7050 Al alloy plate during solution heat treatment[J].The Chinese Journal of Nonferrous Metals,2010,20(3):427-434.
• [15]Wang D,Xiao B L,Wang Q Z,et al.Friction stir welding of Si Cp/2009Al composite plate[J].Materials and Design,2013,47:243-247.
• [16]田荣璋,王祝堂.铝合金及其加工手册(Ⅱ)[M].长沙:中南大学出版社,2000.
• [17]耿林,吴昆.中国材料工程大典:第10卷,复合材料工程[M].北京:化学工业出版社,2006:485-547.

文章评论(Comment)：