赵红亮,李荣平,胡冠奇,翁康荣,陈起

• 1:郑州大学材料科学与工程学院
• 2:登电集团铝加工有限公司

摘要(Abstract)：

利用光学显微镜(OM)和数字电桥等手段研究了不同退火温度对铸轧3003电子铝箔坯料的显微组织和成品铝箔腐蚀后表面质量的影响。结果表明:0.55 mm厚3003坯料的再结晶开始温度为295℃,终了温度为320℃;在320～460℃之间退火时,再结晶晶粒尺寸随退火温度的升高而逐渐减小。经过295℃退火处理的0.55 mm厚坯料由于内部晶粒大小不一,导致冷轧后成品铝箔表面腐蚀后出现大量腐蚀条纹,而退火温度提高到320℃时,成品铝箔腐蚀后表面质量较好。

关键词(KeyWords)： 再结晶退火;3003;显微组织;腐蚀

Abstract:

Keywords:

基金项目(Foundation):

作者(Author): 赵红亮,李荣平,胡冠奇,翁康荣,陈起

DOI: 10.13289/j.issn.1009-6264.2011.11.021

参考文献(References)：

• [1]刘建文,涂益友,蒋建清.AA3003合金铸轧板预析出相对再结晶温组织的影响[J].特种铸造及有色合金,2010,30(1):67-70.LIU Jian-wen,TU Yi-you,JIANG Jian-qing.Influence of pre-precipitation on recrystallization structure and recrystallization temperature in AA3003twin roll cast aluminum strips[J].Special Casting&Nonferrous Alloys,2010,30(1):67-70.
• [2]杨余良,张安乐,张芳.铸轧3003板坯深加工时晶粒组织的控制[J].铝加工,2008(4):29-31.YANG Yu-liang,ZHANG An-le,ZHANG Fang.Grain structure control of cast-rolled 3003 blank in deep processing[J].Aluminum Fabrication,2008(4):29-31.
• [3]冯小平.提高电解电容器阴(负)极用铝箔质量的工艺措施[J].铝加工,2005(5):48-49.FENG Xiao-ping.Process countermeasures of improving the quality of cathode aluminum foil for electrolytic capacitor[J].Aluminum Fabrication,2005(5):48-49.
• [4]蔡健,王百红,梁慧强,等.电解铝液生产电解电容器负极箔的关健技术[J].轻合金加工技术,2004,32(9):17-19.CAI Jian,WANG Bai-hong,LIANG Hui-qiang,et al.The key technic of producing cathode foil electrolysis capacitance with electrolytic aluminum melt[J].Light Alloy Fabrication Technology,2004,32(9):17-19.
• [5]BIROL Y.Homogenization of a twin-roll cast thin Al-Mn strip[J].Journal of Alloys and Compounds,2009,471:122-127.
• [6]LI Y J,ARNBERG L.Evolution of eutectic intermetallic particle in DC-cast AA3003 alloy during heating and homogenization[J].Materials Scienceand Engineering A,2003,437:130-135.
• [7]Humphreys F J,Hatherly M.Recrystallization and Related Annealing Phenomena[M].Pergamon,Oxford,1995.
• [8]刘建文,涂益友,孙玉琴,等.析出相对3003铝箔再结晶组织的影响[J].特种铸造及有色合金,2009,29(11):1607-1609.LIU Jian-wen,TU Yi-you,SUN Yu-qin,et al.Effects of precipitates on recrystallized structure in 3003 aluminum foils[J].Special Casting&Nonferrous Alloys,2009,29(11):1607-1609.
• [9]张新明,吴文祥,唐建国,等.预析出对冷轧3003铝合金析出行为及再结晶晶粒尺寸的影响[J].中南大学学报:自然科学版,2006,37(2):212-216.ZHANG Xin-ming,WU Wen-xiang,TANG Jian-guo,et al.Effect of pre-precipitation on precipitation behavior and recrystallization grain size of coldrolled 3003 aluminium alloy[J].J Cent South Univ:Science and Technology,2006,37(2):212-216.
• [10]Altenpohl D.Aluminium and Aluminiumle Gierungen[M].Berlin:Springer Verlag,1965.
• [11]Li Y J,Arnberg L.Solidification structure of DC-cast AA3003 alloy and its influence on homogenization[J].Aluminium,2002,78(10):834-839.
• [12]Cahn J W.Nucleation on dislocations[J].Acta Metall,1957,5(3):169-172.

文章评论(Comment)：