胡祖麒,万里,吴树森,林冲

• 1:华中科技大学材料成形与模具国家重点实验室

摘要(Abstract)：

对常规压铸(DC)和真空压铸(VDC)Al-Mg-Si-Mn合金平板铸件的微观组织、力学性能和疲劳性能进行研究,并且用SEM和EDS等手段分析了断口形貌。结果表明:Al-Mg-Si-Mn合金的微观组织主要由初生α-Al,[Al+Mg2Si]共晶区以及Al15(Fe,Mn)3Si2颗粒构成。常规压铸试样和真空压铸试样的抗拉强度(Rm)、屈服强度(Rp 0.2)、弹性模量(E)和伸长率(A)分别为321 MPa,205 MPa,54 MPa和3.9%,以及331 MPa,210 MPa,55 MPa和4.4%。真空压铸试样的裂纹扩展速率曲线斜率(2.824)低于常规压铸试样(3.693),因而真空压铸试样的抗疲劳性能较好。试样的拉伸断口显示出大量脆性断裂特点即解理平面,而疲劳断口则可清晰观察到疲劳条纹和撕裂棱。

关键词(KeyWords)： 真空压铸;Al-Mg-Si-Mn系压铸铝合金;力学性能;裂纹扩展速率;断口形貌

Abstract:

Keywords:

基金项目(Foundation): 广东省省部产学研结合重大专项2012A090300016

作者(Author): 胡祖麒,万里,吴树森,林冲

DOI: 10.13289/j.issn.1009-6264.2014.05.010

参考文献(References)：

• [1]Kaufmann H,Uggowitzer P J.Metallurgy and Processing of High-Integrity Light Metal Pressure Castings[M].Schiele&Schn,2007.
• [2]Metal Handbook:Casting[M].15thed.Metal Park:ASM International,1988.
• [3]万里,赵芸芸,潘欢,等.铝合金高真空压铸技术的开发及应用[J].特种铸造及有色合金,2008,28(11):858-861.WAN Li,ZHAO Yun-yun,PAN Huan,et al.Development and application of high vacuum die casting technology[J].Special Casting&Nonferrous Alloys,2008,28(11):858-861.
• [4]万里,刘后尧,吴树森,等.轿车底盘铝合金后副车架的压铸技术开发[J].特种铸造及有色合金,2012,32(2):145-148.WAN Li,LIU Hou-yao,WU Shu-sen,et al.Research on vacuum die casting technology for Al alloy chassis rear sub-frame of GAC trumpche car.Special Casting&Nonferrous Alloys,2012,32(2):145-148.
• [5]万里,潘欢,罗吉荣.高真空压铸技术及高强韧压铸铝合金开发和应用的现状及前景[J].特种铸造及有色合金,2007,27(12):939-942.WAN Li,PAN Huan,LUO Ji-rong.Development and application of vacuum die cast technology and high-toughness die cast aluminum alloy[J].Special Casting&Nonferrous Alloys,2007,27(12):939-942.
• [6]Franke R,Dragulin D,Zovi A,et al.Progress in ductile aluminum high pressure die casting alloys for the automotive industry[J].La Metallurgia Italiana,2007,5:21-26.
• [7]Kaufmann H,Uggowitzer P J.Fundamentals of the new recasting process for magnesium alloys[J].Advanced Engineering Materials,2001,3(12):963-967.
• [8]Hielscher U,Sternau H,Koch H,et al.Newly developed die casting alloys with outstanding mechanical properties in the as-cast condition[J].Giesserei(Germany),1998,85(7):62-65.
• [9]Otarawanna S,Gourlay C M,Laukli H I,et al.Microstructure formation in AlSi4MgMn and AlMg5Si2Mn high-pressure die castings[J].Metallurgical and Materials Transactions A-Physical Metallurgy and Materials Science,2009,40A(7):1645-1659.
• [10]Hu Z,Wan L,Wu S,et al.Microstructure and mechanical properties of high strength die-casting Al-Mg-Si-Mn alloy[J].Materials&Design,2012,46:451-456.
• [11]闫锋.强力熔体剪切下LM24及Magsimal-59合金压铸参数优化及定性分析[D].天津理工大学,2011.YAN Feng.Optimization and characterization of LM24 and magsimal-59 HPDC alloys under intensive shearing[D].Tianjin University of Technology,2011.
• [12]北京航空材料研究院.GB/T 6398-2000金属材料疲劳裂纹扩展速率试验方法[S].2000.GB/T 6398-2000 Standard test method for fatigue crack growth rates of metallic materials[S].2000.
• [13]Bournane M,Nedjar M,Sirenko A F.Precipitation in solid solutions of Al-Mg[J].Scripta Materialia,1999,40(3):375-382.
• [14]Ji S,Watson D,Fan Z,et al.Development of a super ductile diecast Al-Mg-Si alloy[J].Materials Science and Engineering A,2012,556:824-833.
• [15]Belov N A,Eskin D G,Aksenov A A.Chapter1-Alloys of the Al-Fe-Mn-Si System[M].Multicomponent Phase Diagrams:Application for Commercial Aluminum Alloys,Oxford:2005:1-46.
• [16]Crepau P N.“Effect of iron in Al-Si casting alloys:a critical review[J].AFS Transactions,1995,103:361-366.
• [17]Paris P,Erdogan F.A critical analysis of crack propagation laws[J].J Basic Eng Trans,1963,4(85):528-534.
• [18]Greven K,Dragulin D.Proceeding of the 2nd International Conference on Light Metals Technology[C]//LKR-Verlag,2005.
• [19]Johannesson B,Cáceres C H.Effect of Si additions and heat treatment on the mechanical behaviour of an Al-5Mg cast alloy[J].International Journal of Cast Metals Research,2004,17(2):94-98.
• [20]Ceschini L,Boromei I,Morri A,et al.Microstructure,tensile and fatigue properties of the Al-10%Si-2%Cu alloy with different Fe and Mn content cast under controlled conditions[J].Journal of Materials Processing Technology,2009,209(15-16):5669-5679.
• [21]Kuijpers N C W,Vermolen F J,Vuik C,et al.The dependence of theβ-AlFeSi toα-Al(FeMn)Si transformation kinetics in Al-Mg-Si alloys on the alloying elements[J].Materials Science and Engineering A,2005,394(1-2):9-19.

文章评论(Comment)：