许晓嫦,刘志义,党朋,于文斌,宁爱林

• 1:中南大学材料科学与工程学院
• 2:中南大学材料科学与工程学院
• 3:中南大学材料科学与工程学院
• 4:中南大学材料科学与工程学院

摘要(Abstract)：

通过硬度测试、透射电镜图像和X射线衍射图谱分析,研究了6063铝合金在压缩变形过程中的显微组织和性能变化。结果表明:在压缩变形初期,6063铝合金在过饱和态,峰时效态和过时效态的硬度均呈近似直线上升,它们的硬化能力按下列顺序降低:峰时效、过饱和态、过时效。出现硬度下降后,压缩率则按上列顺序增大。强塑性变形过程中出现析出相析出和回溶有利于降低加工硬化引起的脆性。

关键词(KeyWords)： 6063铝合金;强塑性变形;回溶;时效;压缩变形

Abstract:

Keywords:

基金项目(Foundation): 国家自然科学基金资助项目(50571069);; 湖南省自然科学基金资助项目(05JJ40005)

作者(Author): 许晓嫦,刘志义,党朋,于文斌,宁爱林

参考文献(References)：

• [1]Shin D H,Kim I,Kim J,et al.Microstructure development during equal-channel angular pressing of titanium[J].Acta Mater,2003,51:983-996.
• [2]May J,Hoppel H W,Goken M.Strain rate sensitivity of ultrafine-grained aluminum processed by severe plastic deformation[J].Scripta Materials,2005,52:189-194.
• [3]Krasilnikov N,Lojkowski W,Pakiela Z,Valiev R.Tensile strength and ductility of ultra-fine-grained nickel processed by severe plastic deformation[J].Materials Science and Engineering A,2005,397:330-337.
• [4]Hebesberger T,Stuwe H P,Vorhauer A,et al.Structure of Cu deformed by high pressure torsion[J].Acta Mater,2005,53:393-402.
• [5]许晓嫦,刘志义,谭曼玲,等.时效析出相在强变形过程中的室温回归现象[J].材料热处理学报,2004,25(6):71-76.XU Xiaochang,LIU Zhiyi,TAN Manling,et al.Retrogressive phenomenon of aged precipitates caused by severe plastic deformation[J].Trans Mater HeatTreat,2004,25(6):71-76.
• [6]许晓嫦,刘志义,于文斌,谭曼玲.室温强塑性变形下回溶和再析出的机理研究[J].材料科学与工艺,2005,13,(2):178-181.XU Xiaochang,LIU Zhiyi,TAN Manling,LIU Yuejun.Mechanism of re-dissolution and re-precipitation of second phases in aluminum alloy under severeplastic deformation[J].Materials Science and Technology,2005,13(2):178-181.
• [7]Gutierrez Vrrutia I,Munoz-Morris M A,Morris D G.The effect of coarse second-phase particles and fine precipitates on microstructure refinement andmechanical properties of severely deformed Al alloy[J].Material Science and Engineering A,2005,394:399-410.
• [8]Murayama M,Horita Z,Hono K.Microstructure of two-phase Al-1.7 at%Cu alloy deformed by equal-channel angular pressing[J].Acta Mater,2001,49:41-29.
• [9]Liu Z Y,Liang G X,Wang E D.Effect of equal channel angular pressing on structure of Al alloy 2024[J].Trans Nonferrous Met Soc China,1997,(7):160-162.
• [10]Uniu N,Gable B M,Shiflet G J,et al.The effect of cold work on the precipitation ofΩandθ′in a ternary Al-Cu_Mg alloy[J].Materials Science Form,2002,396-402;801-806.
• [11]Esmaeill S,Wang X,Lloyd D J,et al.On the precipitation-hardening behavior of the 6063-Cu alloy AA6111[J].Metallurgical and Materials Transaction A.2003,34:751-763.
• [12]Prangnell P H,Bowen J R,Apps P J.Ultra-fine grain structure in aluminum alloys be severe deformation processing[J].Material Science and Engineering A,2004,375-377:178-185.
• [13]Genki S,Zenji H,Terence G L.Grain refinement and superplasticity in an aluminum alloy processed by high-pressure torsion[J].Material Science andEngineering A,2005,393:344-345.

文章评论(Comment)：