王会珍,李云凯,李树奎,王富耻

• 1:北京理工大学材料学院

摘要(Abstract)：

对某新型超高强度钢(83钢)进行950℃淬火不同温度回火(200～700℃),除测定其静态力学性能外,利用霍普金森杆采用动态压缩和强迫剪切方法对其动态压缩性能进行了研究,并分析了回火温度对其性能的影响。结果表明,83钢在250～450℃范围内回火后存在回火脆性,塑韧性较差,绝热剪切破坏较严重,在其他温度下回火,随回火温度的升高,材料塑韧性和绝热剪切破坏程度逐步改善。

关键词(KeyWords)： 热处理工艺;静态力学性能;动态压缩性能

Abstract:

Keywords:

基金项目(Foundation):

作者(Author): 王会珍,李云凯,李树奎,王富耻

DOI: 10.13289/j.issn.1009-6264.2010.09.017

参考文献(References)：

• [1]王礼立,余同希,李永池.冲击动力学进展[M].合肥:中国科学技术大学出版社,1992.
• [2]Meunier Y,Beatty J H.Shock Waves and High Strain Rate Phenomena in Metals[M].New York:Marcel Dekker Inc,1992.
• [3]Meyers M A.Dynamic Behavior of Materials[M].New York:John Wiley&Sons Inc,1994.
• [4]Woei-Shyan Lee,Chen-Yang Liu,Tao-Hsing Chen.Adiabatic shearing behavior of different steels under extreme high shear loading[J].Journal of Nuclear Materials,2008,374(1-2):313-319.
• [5]Xinqin Liu,Chengwen Tan,Jing Zhang,et al.Correlation of adiabatic shearing behavior with fracture in Ti-6Al-4V alloys with different microstructures[J].International Journal of Impact Engineering,2009,36(9):1143-1149.
• [6]Xinqin Liu,Chengwen Tan,Jing Zhang.Influence of microstructure and strain rate on adiabatic shearing behavior in Ti-6Al-4V alloys[J].Materials Science and Engineering A,2009,501(1-2):30-36.
• [7]孙坤,程兴旺,王富耻,等.组织及应变率对TC6钛合金绝热剪切敏感性的影响[J].稀有金属材料与工程,2008,37(10):1856-1860.SUN Kun,CHENG Xing-wang,WANG Fu-chi,et al.Study on sensitivity of adiabatic shear of TC6alloy under different strain rate and morphology[J].Rare Metal Materials and Engineering,2008,37(10):1856-1860.
• [8]冀建平,才鸿年,李树奎.铁素体含量对亚共析钢绝热剪切变形的影响[J].兵器材料科学与工程,2007,30(5):25-28.JI Jian-ping,CAI Hong-nian,LI Shu-kui.Influence of ferrite content on adiabatic shear deformation of hypoeutectoid steel[J].Ordnance Material Science and Engineering,2007,30(5):25-28.
• [9]苏铁健,王超,李树奎,等.钢的强导比与绝热剪切敏感性关系的研究[J].兵器材料科学与工程,2005,28(2):1-4.SU Tie-jian,WANG Chao,LI Shu-kui,et al.Study of relationship between the ratio of strength to thermal conductivity and adiabatic Shearing sensitivity of steels[J].Ordnance Material Science and Engineering,2005,28(2):1-4.

文章评论(Comment)：